TAA761 and other historic classic chips in german
http://www.ic-ts-histo.de/fad/ics/taa761/taa761fa.htm

On Sun, Mar 3, 2019 at 11:10 PM ludwig jaffe <ludwig.jaffe@gmail.com> wrote:

Hi Hagen,

we could make a combo chip:

NE555, some LM741, and some CD4066 (transfer gate)

UC3845, UC3843 (simple PWM chip for switch mode power supply)

So geeks could combine the chips using transfer gates :-)

Or lets think about a simple analog geeky chip, that contains:

saw tooth generator, comparator, rs latch, error-amps (UC3845)

while the the saw tooth generator is replaced with a NE555 (transfer gate,

or just fitting the ne 555 instead of the internal uc3845 saw tooth generator)

The Op-Amp in the UC3845 may be replaced with a 741 or similar simple op amp.

So we have an universal circuit containing:

-OPAMPS (741, LM324 or similar)

-universal SAWTOOTH-Generators (NE555)

-RS-Latch (NE555 also has a latch) for use in fake UC3845

-the rest used in UC3845

the transfer gates are used as pin mux so we can access internal stuff

of the modified UC3845 and split it into, OP-AMPS, NE555 and so on.

So having a programable simple analog circuit would be cool.

Also a TL431 programable z-diode woud be cool as well as

TAA 761 open collector op-amp.

So here we could combine TL431 with TAA761 open collector

op amp.

We would have an analog "fpga"

What do you think?

Cheers,

Ludwig

On Sun, Mar 3, 2019 at 2:13 PM Hagen SANKOWSKI <hsank@posteo.de> wrote:

Hello List.

Today in our weekly Mumble Session we talked about a smaller chip, which
could be realized before the Northpoint.

The Reason is mostly, that the Northpoint (as an small MCU) - beside the
Standard Cells - also has some challenging Analog Stuff (like the ADC,
Pad-Cells) which set the hurdle a little bit high.

We need some physical haptic fancy / shiny silicon before which gives us
also a realistic way to verify our simulation after model measurement we
do with PearlRiver. Something we could hand over to other people and
which blinks..

Well, we came across the well-known "triple-5 chip". The original NE555
[0] was developed by the Swiss electronics engineer Hans Camenzind [1]
and get cloned by nearly all silicon firms on the market in this era.
Great starting points for our CMOS-based clone are the wikipedia site
and the free eBook [2] of the original author. I strongly recommend
everybody to read this great book!

Mostly the 555 chips are in the -55 to +125 C temperature range - the
same we assume for our technology. And the voltage supply goes up to +18
Volt, I already saw 555 which worked with higher voltage. If we like, we
could using our BiCMOS feature for the output driver - driving the same
current with less power consumption.

The 555 chip has a legendary status between electronic engineers, radio
amateurs and tinkers. And some of them writing obeisance on hackaday.com
still in 2018 [3]. Many variations of the chip are still in production.
Short - the 555 would be a great try-out for LibreSilicon! And I am
proud to announce that Ferenc will be our Lead for the "LS 555"
(LibreSilicon triple-5). Thanks Ferenc for your commitment!

Regards,
Hagen.

[0] https://en.wikipedia.org/wiki/555_timer_IC
[1] https://en.wikipedia.org/wiki/Hans_Camenzind
[2] http://www.designinganalogchips.com/
[3] https://hackaday.com/2018/10/10/the-555-and-how-it-got-that-way/
_______________________________________________
Libre-silicon-devel mailing list
Libre-silicon-devel@list.libresilicon.com
http://list.libresilicon.com/mailman/listinfo/libre-silicon-devel